"DEVELOPMENT OF A DEVICE FOR DETERMINING WORK ELECTRON OUTPUT "
DOI:
https://doi.org/10.31489/2020No1/127-131Keywords:
non-destructive testing, metal part, surface, capacitor, contact potential difference.Abstract
The surface is the most important component of metal parts and it is necessary to control its condition at all stages of the life cycle of the part - during its production, operation and repair. To carry out reliable non-destructive testing of metal parts, specially developed tools and methods for its use are necessary. The measuring electrode of the sensor of the measuring device of the contact potential difference and the surface of the metal part to be controlled form a capacitor, between the plates of which the contact potential difference occurs. The sensor of the device is a kind of intermediary between the contact potential difference and the measuring circuit. The portable complex for measuring the contact potential difference developed by the authors on the basis of a portable digital oscilloscope allows non-destructive testing of the surface of metal parts during their production, operation or repair to be performed continuously.
References
"1 Betsofen S.Ya., Osintsev O.E., Knyazev M.I., Dolgova M.I., et al. Quantitative phase analysis of Al-Cu-Li-Mg alloys. Bulletin of the Moscow Aviation Institute. 2016, Vol. 23, No. 4, pp. 181–188.
Musokhranov M.V. Technological support for the quality of the surface layer of the guiding elements of mechanical engineering. Diss. of Techn. Sciences Cand. Moscow, Bauman MSTU, 2006, 138 p.
Zharin A.L., Gusev O.K., Svistun A.I., Tyavlovsky A.K. Friction surface control by contact potential difference methods // Izvestiya TulGU. Technical science. 2011. Issue. 5. Part 2. - P. 286-295.
Kocharov E.A. Physical methods in the control of materials and the development of high technology. Moscow, VVIA named after prof. N.E. Zhukovsky. 2008, 447 p.
Kryachko V.V., Levin M.N., Tatarintsev A.V., et al. A non-contact method for studying the charge state of a semiconductor – insulator interface. Journal of Technical Physics. 2004, Vol. 74, Issue 10, pp. 128 – 133.
Loskutov S.V. Regularities of the formation of the energy relief of a metal surface. News of the Zaporizhzhyan State University. 1999, No. 1, pp. 138 – 142.
Petrov L.M., Plikhunov V.V. Determination of the energy state of the surface of structural metallic materials after technological influences. Aviation industry. 2012, No. 1, pp. 22 – 26.
Grachev A.V., Churakov P.P. Converter of parameters of non-contact capacitive sensors for conductodielcometric measurements // Bulletin of the Samara Scientific Center of the Russian Academy of Sciences. 2016. Vol. 18. No. 4 (7). - P. 1363-1368.
Tyavlovsky A.K., Zharin A.L. Analysis of the method of measuring the surface potential of dielectrics according to the scheme of current compensation. Instruments and methods of measurements. 2011, No. 2 (3), pp. 136 – 144.
Kompaneyets I.V., Komolov V.M., Shkilko A.M. Assessment of the sensitivity of the contact potential difference meter. Bulletin of NTU ""KhPI"": Series ""New Solutions in Modern Technologies"". 2010. No. 46, pp. 89 – 94.
Kolesnikov V.P. Electrometry. Theoretical foundations of electrometry methods. - Perm, 2019. - 264 p.
Panteleev K.V. Methods and means of measuring the contact potential difference based on the analysis of the compensation dependence of the Kelvin probe. Abstract. Diss. of Candidate of Technical Sciences. Minsk: Belarusian Nat. tech. Univ. 2016, 26 p.
Oleshko V.S., Yurov V.M. Fluctuation of the contact potential difference in determining the work function of electrons from structural materials by the ionization method. Proceeding of the 10th Intern. Conf. “Chaos and structures in nonlinear systems. Theory and experiment”, Almaty, 2017, pp. 165 – 169.
Oleshko V.S., Guchenko S.A., Yurov V.M. Determination of the surface energy of solid metals. Proceeding of the XIV Int. Scientific Conf. “Solid State Physics, Functional Materials, and New Technologies” (FTT-2018), Bishkek-Karaganda, 2018, pp. 124-128.
Yurov V.M., Oleshko V.S. The impact of the environment on the contact potential difference of metal machine parts. Eurasian Physical Technical Journal. 2019, Vol. 16, No.1 (31), pp. 99 – 108.
"
